Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hello, I've been asked to support Call Manager and I am getting a "Registration: Security Error on phone" while reviewing the configuration of Call Manger, I ran across the certificate screen that indicated some certificates has expired. I see there ...
Hi, how can I get my 8841, 7821 and 6825 (DECT-VoIP) 3PCC phones to add the "sip.instance" parameter in the SIP messages?My phones do not send "gruu" in the Supported header, nor add the "instance" in the Contact header. Here is a sample log from a S...
I've never noticed the "Lower your voice Alert". A user happened to find it. You can turn it off via the phone settings. I am trying to find out if it can be globally turned off. Also, when was this feature implemented. Not finding anything in ...
Hi Folks, I am wondering if anyone knows of a wireless headset that will work with CUAC-A. I have a few DECT headsets that I have connected to a 7821 IP phone and have had limited success with having getting the headset to control the call. One pos...
Hi Guys We have 7861 and 3905 Phone that we want to configure in FUJI 16.9.2 on Cisco 4451. But under ephone type, there isnt any option of 7861 or even the 3905. Please if someone can advice. Regards
Hi guys, I'm facing issues when trying to register phones model 8845 in my 2960x cisco switch. Recently we added that switch to the network, we moved half of the phones to this switch and the specific SIP 8845 model phones do not register. Other SCCP...
Hello, A customer of ours is reporting that all their Cisco 8861 Phones with the CP-8800-Audio-28-KEM module are acting strangely. The KEM modules are constantly rebooting, a daily act almost. The Cisco Call Manager is version 11.5.1.12900-21 with la...
when connect it starts but does not come to the home screen, then it restarts again.Also Last LED's are amber and it does not turn to green
Hi Guys. We have the Cisco 4451 that we want to convert from SRST Mode to CME. Please if some one can tell us the commands. The licences details is as follows: If you require further assistance please contact us by sending email toexport@cisco.com. S...
Hi all thereIs there any way to count the number of calls goes outside via PSTN in the last month or something like this.is RTMT do that? and how to do that? Thanks in advance.
Anyone have a recommended stable firmware image version. I loaded Release 10.2(5.215)ES as it's the most recent but now the phones just fall off the network after about 10 seconds. I'm rolling back to a older version but wondering if someone can reco...
Hi all, in order to do some testing, we'd like to connect to the CUCM Sandbox 12.5 via VPN. Can you please let me know which Cisco Phones we have to order for it?We've found the following: SPA525G2 (https://www.cisco.com/c/en/us/products/collateral/c...
Hi all,We recently had the Cisco 8845 multi-line phones installed in our group. When we had our old 7965s, they were set up so that only the main line (the first listed) would actually ring. The rest of the lines would flash and the number calling wo...
Just upgrade to 11.5 in UCM. (UCM PUB/2 UCM SUBS, UCON PUB/UCON SUB and Presence PUB/SUB)Since upgrade Plantronics CS 540 with APC-43 No ring tones are detected in Headset.
Hi Team, Can i configure VG224 gateway with CME 10.5 for fax and analog lines. If yes, what will be the procedure. Regards,call manager express, CME, Voice Gateways, VG224Vicky
