Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
I have a user with a voicemail box whose greeting states for urgent calls to press 0 to transfer to another extension. This works if the callers press 0 quick enough. Is there a way to extend the time between the end of the greeting and when the call...
We have the following three model 7970, 7941 and 7965. Want to program on third party call control. Please advise. Their Mac # 001F6C800073, 001FCAE79DA4 and 002155531E02.
Hi all,My setup a bunch of SIP phone numbers I own that forward to an external phone number. For example, I own 2222222222 on our SIP Trunk. We then have a translation pattern that translates the called number to “3333333333”, which is an external nu...
Hello,I wonder if the following concept can be achieved in the CUCM.I want to translate external number0******7133 to the internal 2133.We use the external number as DDI for the conferences but would like to have employees connection to the dial in v...
I am running Call Manager version 9.1.1 at my company and am needing some guidance. We have a number that our employees can call (a hotline type number) that when the line answers an automated message is played presenting the caller with a few optio...
Hi,I am seeing Avaya Packed drops every third packed when do the extended ping from router or switch. Anyone has any idea about this behaviours?Switch#ping 10.10.10.1 repeat 20Type escape sequence to abort.Sending 20, 100-byte ICMP Echos to 10.10.10....
Hi,I have a Voice gw 2921 with IOS 15.1M with cucm 8.6Calls will go through VIC2-4FXO card. the voice gateway is configured as h323 with the CUCMThe problem is that Incoming calls sometimes display the calling number and sometimes display "Unknown N...
The following is the message I get when the post install / installing db components are at about 83% complete. I have rebuilt the server as multiple TAC cases have revealed that my CUCM server is possibly corrupted. This is the exact same thing that ...
Hi!I have a Cisaco router 2821+CME with 9 port swith ethernet module.How can I connect voip phones to my router through ethernet switch module inside router.I tried address interface vlan - without results. Help me please.
I'm running CUCM 12.5 in mixed-mode. I've configured and enabled encryption for handsets fine. But when I configure a telepresence units (Roomkit, DX, etc on CE9.8) with any form of encryption, the unit fails to register. I can't see anything on Cisc...
Hi,I have a 2901 with 1 x PVDM3-32 and 1x PVDM3-64The only interface card that uses the DSP's is a VWIC2-2MFT-T1/E1I want to add a transcoder using the LTE interface, I think I should have enough DSP's, but max sessions says <0-0>As far as I can see ...
Hello,Just want to know if IP Phone 3905 supports Extension mobility feature with CUCM 12.0.I went through the 3905 Data Sheets but those were not updated one.Also i did not found the feature mentioned for 3905 in Unified CM Phone Feature List in Uni...
Can voice traffic handle asymmetric routing? Can any issue arise when the outbound path is different from the inbound? The voice provider is an online provider.
Hi, Can someone tell if in product part number: BE6K-START-MTG35 are also included CUWL Professional? I mean the 35 users on CUCM? Thanks JH
i guys, do any of you know the CLI commands for me to get a file from my CUCM to my FTP server? My TAC engineer is on his off hours. He asked me to run this command: utils network capture eth0 file packets count 1000000 size all That is straight fo...
