Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
I have reset the private password phrase but when I try to install the new subscriber server it errors on the private password phrase. Error is "Passwords do not match or there is a Network connection error" the systems are on the same switch, there ...
Hi All,Anyway to shorten the call setup time for CallManager to PSTN through voice gateway and CCME to PSTN? Seems the call setup time by default to PSTN is longer then using traditional PBX.Best Regards,Teru Lei
Hi, can anyone advise how you configure a PRI that has only 20 channels not the usual 30?
A customer has CM4.2 with a H.323 voice gateway for PSTN acces and Multimedia terminals with an H.323 client for telephony.Calls from the PSTN are sent with the calling number in the H.323 setup to the H.323 client.After an upgrade to CUCM6.0 the cal...
Previous to the upgrade from 3.3, we could dial *, plus the 4 digit extension and transfer a call directly to individual mail boxes. Now, it takes me to the call handler and forwards me automatically to an operator extension, anytime I dial * plus a...
Hello,I have two router : a 3745 with VIC-2E&M and a 1751V with VIC-2E&M.I want to tranfer call from the 1751V to the 3745 with these cards.(router )E&M <-> E&M (router)Is it possible? How to do? How about connector and pinouts Thenk you very much.
I received a complaint that a user is not recieving calls to his extension and the voicemail light was not turning on. I have tried these solutions but ended up in a worse situation than I started. I was able to dial the extension but now I ust get a...
Hi!I have defined Meet-Me number. How can I restrict access to this number (calls from PSTN), in the way that only specific external telephone number can access this pattern?Is this possible?thx
Hi!Maybe someone have encountered this problem too...When secretary wants to transfer incoming call from outside to one of employees extention there is a delay about 5 sec. She uses consult transfer and when she presses "Transfer" softkey second time...
how to manipulate the outgoing number?forexample, phone registers on the router with internal number 1006, and also appears dial-peer 1006$, and calls I can make only INTERNAL! FROM 1006 to 1007 ans so on.But I cann't call PRI number, like 212345dial...
While inspecting the config of our UC520 I see it makes extensive use of BVI interfaces and bridge-groups. I see that the 802.11 radio and VLAN1 interfaces are part of a bridge-group 1 with a BVI interface setup for them and that my Voice VLAN also ...
Hi !I am getting the following debug output on my MGCP gateway when I want to make an inbound call. The outbound call works fine. There is 910 extension. Any ideas?thanks,KO08_2812(config-if)# *Jan 28 17:13:10.684: ISDN Se0/0/0:15 Q931: RX <- SETUP ...
I have in a lab environment a UC520 with 4 phones. 7941, 7940, 7911, 7905.I have issues with the 7941. it has registered fine but when I pick the handset up I get no dial tone, the other phones are fine. When I call the other phones from the 7941 the...
Hi,I am working with 8 analogues lines for a UCME / H323 gateway (Cisco 2811). I know the Telco can configure the 8 lines in a rotary upon request but in the event that they are not. Are there any configurations on the voice ports for especially for ...
Why is it that the default UC520 setup uses a /30 subnet for the CUE configuration? Can I do without that and simply assign an IP to CUE that is the same as my voice VLAN?Thanks,Diego
