Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
We have Unity version: 11.5.1.23900-30. A customer reports a repeated notification email is sent after listening to message. There is a possibility the email address could be also set as a notification device on another mailbox. Is there a way to sea...
hi all,i think there is an option to enable mail notification for sudden ip phone and DX70 goes unregister to take action.i mean i need to get mail of CEO`s ip phone was unregistered or his DX70 too.any guide for this?
Hi All,We are planning to upgrade our current CME 2900 series with a newer Cisco 8200 series. Additionally, we are also looking to replace our existing Cisco 8821 wireless phones with the newer Wireless Phone 840 and 860 models.I'm curious if the new...
Hi folksIs there a way to send the dtmf attached on the sip invite, or in somewhere in the signaling process on an enbloc string like 81 1111 1111 - 1234 (where 81 1111 1111 is our did, and the 1234 is the dtmf)?Thank you in advance.
Hi guys, we are actually struggling to integrate the new 840 phones in the Jabber client as controlled device. It worked with the 79xx, 88xx, all the used phones before, regardless if wired or wireless, the config on the callmanager seems to be corre...
Hi, experts, Trying to regenerate an expired certificate due to a late check while running cucm 11.5.Can I restart the service by regenerating the expired certificate?Or do I have to get a new one when it expires? Expired certificates are listed be...
How to use Webex Room Bar in CUCM 11.5 version?Hello, heroes of cisco I have a question. my customer company is using CUCM version 11.5 The customer wants to use the Cisco Room Bar without upgrading the version of CUCM. I know that the Room Bar templ...
Howdy,We have our first headset in our district and it's tied to a 8851. However, I can't adjust the sidetone volume. It's on low and it's grayed out. With this being our first headset, we don't have the headset service setup or anything like that...
Hey all, I have a user that is wanting their voicemails to be picked up on their cell phone instead of their desk phone. Is there a way to make this function with 100% consistency? Currently each user with a work provided cell phone has a RD profile ...
I just hired on with my company and they've put me in charge of their Cisco Unified Communications Manager (on version 11.5.1). Someone else set it up prior to me joining the company. I have zero prior experience with this but so far have managed t...
The Spectrum voice engineer said the Division header(highlighted below) that Cisco phone system sent to spectrum. This header is causing the problem on their systems. Thus, their system are rejecting the calls. After the Division header removed, all ...
Hello all ,When we try to call to specific destination , the call disconnect .The scenario is : CUCM->SIP TRUNK TO Provider->providerwe got error 483 "too many hops"The provider of calls request to change the amount of MAX-FORWARDS in PBX .How we can...
Anyone know a report or DB query that can show route pattern usage? We are changing our PSTN access code and want to see # of calls using old code versus new code. Currently both old/new codes are active.Would have thought that the CDR "Route Pattern...
Hi all, we have a CUBE that is choosing a new outbound dialpeer upon receiving a REFER. How can I get it to maintain its current connection? I've tried a few refer-related commands in the CUBE, hoping they would preserve the existing outbound connect...
Hello there!Just got my CCME working with my C7970 and registering on the ISP VOIP trunk.Can make calls but can't receive them. For what I can see with the debug voice dialpeer all, I get a match on multiple dial-peers:-------------------------------...
