Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
All, Back in the 7.X days I used to use Cisco Phone Designer to upload ringtones to specific phones. We have now upgraded to CUCM 10.5. I need to upload a ringtone to 12 phones, more specifically to Extension Mobility Profiles, but I dot want anybod...
This is often referred to as "Active" recording as it uses a SIP trunk to record a duplicate stream of audio from the recorded phones via the phones own built in bridge.Not all phones are supported, and the best description I have found states "All 3...
Dear All, I have Call diagnostics enabled (enabled regardless of CDR enabled flag), but varVQMetrics does not show up? Is there any other settings to be enabled for the same? Thanks in advance
I work for a company and we have 250+ remote sites and we are starting to use the cisco 8811 phones in replacement of the cisco 7962 model phones. We originally had to load the device pack on our CUCM System version: 8.6.2.23900-10 cluster to suppor...
Setting up a CME 8.6 running on a 2821 with 7961's running in SCCP. Management wants for who ever picks up any of four ringable lines to show up on the individual employee's call appearance. Lines are pots. What I was thinking is having the lines ...
Hello All, It's been awhile since I've posted here....hopefully I can get some assistance. I have a customer running CUCM and CUC 9.1 First a little background: I understand CUC looks at original called number by default when searching for a mailb...
Implementing security mechanisms in the Cisco Unified Communications Manager system prevents identity theft of the phones and the Cisco Unified Communications Manager server, data tampering, and call-signaling/media-stream tampering. This Session ...
Hi guys, My client is having Cisco 9971 SIP phones. We already configured for intercoms between these phones and it is working. We are having a software based SIP phone from AMX. We configured that also. But when I am trying intercom call from the ...
Hi All, What is the difference between VG 320 and VG 320-EM. I know VG 320 is an analog gateway which is having 48 analog FXS voice ports with 2 numbers RJ-21 physical interfaces. The description shows for VG 320-EM is 48-port FXS VoIP Gateway w/PV...
Hello Community,Following Szenario,Encrypted Phones SIP 7911, 7931, 7962, 7975 at CUCM 8.6.2 have access long time to the corporate directory and - works fine.Today I add 7821 SIP Phones and they works works fine, but no access to corporate directory...
Hi All, One of our customer migrated their T1 to a Voice Gateway Router. They have two voice gateway and incoming calls using VG2 is working however, incoming calls using VG2 is now working and we are gettting a cause code of Invalid number format (...
Good afternoon, We are currently setting up a parking lot Gate Unit w/ a number pad which customer's press a "Call Press" button, speaks with an agent, agent presses 6 on her phone and the arm lift is triggered - granting the customer access to the p...
Buenas tardes, Por favor si alguien me pudiese orientar en saber que problema puede ser el que indica el log remitido antes., Gracias y saludos, Camilo mmvxi
Hello! Is it possible to provide this inbound call scenario: when somebody calling to hunt pilot number with four members it calls in broadcast for all of them and after 6 sec. of noanswer is forwarding to external mobile number but all of them con...
We just upgrade the firmware on our 7911 phones. When we look at the phones in CallManager 7.0, all of the phones are registered and are running the upgraded firmware version. However, when we look at the phones in RTM 8.0: CallManager | Device | D...
