Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Dear All:I am new with this equipments and I do not have idea how to start to solve this problem.My Cisco IP Phone 7942 does not start after factory reset.It stopped in a Cisco splash screen with a circle with a dot inside.Please, I would be grateful...
I am trying to understand CUBE from the perspective of when you need it and when you don't. For example, I am looking at a configuration that is used by a Avaya PBX that has a pri connection to a router which then has a sip-ua connection to Paet...
I just setup Extension Mobility for our CUCM 8.6 system. I followed the design guide and tested successfully on a couple phones already. However, I wish to enable the EM service on all my phones. The design guide says I have to check the box title...
Hi We have Cisco 8961 with Firmware sip8961.9-3-1-33.Numbers in our corporate directory start with a +. If someone dials from there a number. We have the following issue. During the call the Cisco 8961 can resolve the calling name. But after the call...
Hi all,customer of mine has this old version of CUCMCall Manager 1000 USER1MCS-7825I-3.0-IPC1HW Only MCS 7825I-3000 With P4 3060, 1GB RAM, 80GB HD1CAB-ACIPower Cord-Italian2KEY-CCM-ADMIN-K9=Hardware Security Key for CCM Admin, Rele...
hello,does anyone know if peer firmware sharing is as a feature accessible for 69xx devices? i've found an info, that SIP firmware release 9.1(1) includes this feature, but what about sccp firmware? even in cucm 8.6 there is no option under device co...
Hi AllI have created two different extensions ( i.e 2XXX and 5XX ) on Call manager. What i have to do on Call Manager Setting to configure the route pattern for both extensions.Thanks
Hi all.I want to know if it's possible to force rtp traffic between remote sites to pass through cucm at head quarter.All remote sites have connectivity to hq but not between each other. So the is no audio between ip phones. Only when i make a confer...
Dear NetPro gurus,I notice on the Cisco CallManager's Route Pattern, i can set different types of symbols other than X or numerical numbers.Can someone please kindly explain to mean what are the differences between the following symbols and would be ...
Has anyone ever seen where after the user logs into their Personal Directory, they have to login each time, and if so, what did you do to fix it? I've always had it save your login unless the phone was reset.
I have 2811 gateway running IOS 124.20-T6 (SRST V7.0) and 7942 phones. when the gateway was first installed and SRST enabled, 7942 were able to register to 2811 gateway during SRST. But after a while phone can not register to the ...
Hi Everybody,I'm now using CUCM 8.6 with a publisher and a subscriberNow the publisher is crash and need to be installed again.Is there anything I need to be aware, or just install as normal and restore the CUCM backup?Thanks in advanceSam
Hi All, Does anyone know where I can find a list of which European countries allow toll bypass and which restrict it (like India)? I am having no luck finding the information yet. The only information I've been able to obtain is that Portugal doesn'...
Folks, I am unable to put a /32 mask for an endpoint in a gatekeeper config. It gives me error wrong mask for the IP address. GatekeeperZone local hq Cisco.com 10 .10.10.10Zone subnet hq default enableZone subnet hq 20.20.20.20/32 enable A...
Hi I'm having issues with my UC520 where I'm attempting to configure night service forwarding to a cell phone, but any external-to-internal calls cannot be forwarded to external phone number unless the call has been manually transfered to an extensio...
