Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hello, I am having a strange problem on out customer when the branch fall in STST(Version 9) On the normal operation We configure 3 Hunt Pilots (2599, 2494 and 2495) Each of this Hunt Pilots have a group of DN associated as folows:2599: 2511,2512,...
Hi, I can ping not problem:Pinging 10.20.21.71 with 32 bytes of data:Reply from 10.20.21.71: bytes=32 time<1ms TTL=63Reply from 10.20.21.71: bytes=32 time<1ms TTL=63Reply from 10.20.21.71: bytes=32 time<1ms TTL=63Reply from 10.20.21.71: bytes=32 time...
USB Video Camera support on Cisco IP Phone 8961?Device Information:Cisco 8961Active Load ID: sip8961.9-2-1* Video capabilities enabled on phone configuration of CUCM (Saved, Config Applied, and Reset)Error:"VT3 Camera detected but disabled"Do you kno...
Hi guys,I have a cluster with three CUCM 8.5. We're using a third-party PBX to make external calls, connected with a SIP Trunk.Last week I installed two ISR 3925, created a new route pattern which uses our voice gateways when I call to a specific num...
Not sure how I can fix this, is there a version of CUE 7.0.x that requests the https page ? Problem seems to be CUE requests non https and CallManager beginning with 4.2 made this url https.http://tools.cisco.com/Support/BugToolKit/search/getBugDeta...
Cannot find a working solution to resetting a SIP phone has anyone made this work. I need to reset to factory default and remove the SIP load.
Hello,I noticed that my swap partitions on CUCM servers is now at 0% after upgrading to 8.6(2a)SU1. I checked some old records, and on average it used to be at about 55% on all servers. Is this normal?Thanks,Josh
Hi All,We have deployed the CUCM 8.6 in UCS 210 M2 Server.We faced the problem VM got to hung state.There is reponse when we tried to login via WEB & CLI.We tried to restart the UCS server using Esxi console , it didn't respond.Finally we reboot the ...
Hello,I've got this MCU 3515 unit with following software versions:Software: 5.5.3.0.14EMP: 5.5.3.0.4MCU: 5.5.3.0.5Successfuly integrated with CUCM 6.1 and used as hardware conference bridge.SCCP service was enabled and configured. No problems here: ...
Hey guys,We are in the process of setting up a point to point connection to our Colo datacenter. We are working with a couple of providers and the question that we have is regarding the ISP's QoS capabilities. If our voice traffic traverses the...
Hello guys! When adding a Subscriber server to an existing Publisher in order to create a cluster in the Cisco Communication Manager existing group in the Administration page, if the Subscriber is first in the CUCM group in orde...
Hi,I have Cisco Router 3945 with carts E1 and FXO. The version IOS is: c3900-universalk9-mz.SPA.152-2.T1.binThe communication through E1 passed well without any problem. But I have some problem with FXO communication.The problem that I have actually,...
I converted to a Mac and was hoping all my troubleshooting tools would work in the new environment. Unfortunately when I try to start IP Communicator I get a message "Default Windows Audio Device is either missing or not connected properly. Please r...
i got a problem (ICT Non-Gatekeeper Controlled between CUCM 8.6 and CUCM 4.2)! fast busy tone after the called party pick up the phone.
Hi All!I have the same issue that John Gross had in 2011. Unfortunately, the answer given did not help me. The caller id displays as unknown. This was the issue he had :https://supportforums.cisco.com/thread/2120778This was my configuration to start ...
| User | Count |
|---|---|
| 8 | |
| 4 | |
| 3 | |
| 1 | |
| 1 |
