Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hello All,I did an upgrade on the CUCM from version 7.1.3 to 7.1.5 but discovered that Corporate Directory provision on one of the Phone button is no longer working. Because we use extension mobility the Corporate Directory was subcribed to User Prof...
Hi,I have a phone with external phone mask 6906900 and router group match last 4 digits for calling number and i can call outside without any problemwhen i press forward to mobile number and call the extension it can't call the mobile because it forw...
Hello all,I am doing and install of Unified Business Attendant Console and am running into and error during the install.During the install on the page where you fill out the call manager ip address, the application user you create and its password.I ...
Hi All,I configured CUCM for Multicast MoH and I configured the remote branches to be used as MoHIn Remote branches I added the following configuration:telephony-service srst mode auto-provision none max-ephones 3 max-dn 10 no-reg both ip source-addr...
Hello everybodyi need serious help here,recently in my organisation they upgraded their PSTN phone system, this phone system connects to my Voice gateway cisco 2851 via serial port. when they upgraded their system they asked me to change some configu...
I have finally found a solid correlation to explain why some phone reboot at one of my sites. If I find the time that a phone unregisterd from the UCM 7.1 server and then look at theDHCP lease table - the lease expiry is inevitably five minutes befo...
Hi All,We configured drop-through greetings for the queue in CME. The greetings is too long. Kind of wonder if there is some settings which can enable the "skip" feature allowing the caller press any key to skip the greeting. I couldn't find this set...
Hi,I did a remote site implementation a few months ago. My superior had purchased a Cisco ESW 540 8-Port POE switch to use with the 2811 router there. The 2811 is setup as an H.323 gw. I did not have time to figure out how to configure the switch, a...
Can anyone tell me specifically why the 7940 phone needs 4 licenses? In otherwords, what do those licenses represent? CM license, RTU license, etc?
Hi,I want to know whether there is any way to make dial-peer with certain answer-address to match prior to dial-peep with incoming called-number .T ?
I saw a couple similar posts, but no resolution...I have a simple Sub/Pub cluster running 7.1(5). 7945's and 7965's with SCCP45.9-0-2SR1S register fine with Pub, but I get "Registration Rejected: Security Error" trying to register to Sub.Thoughts?Th...
So I am configuring a Hunt Pilot in which it hunts through certain numbers first then I have a "Forward Hunt no answer" to the destination of *HuntPilotNO".The star in front of it will take it to voicemail. Is there anyway to make it ring more than ...
HelloHere is our current config on a 2851 gatewaysnmp-server community Mystring ROsnmp-server location Mylocationsnmp-server contact My namesnmp-server enable traps snmp authentication linkdown linkup coldstart warmstartsnmp-server enable traps envmo...
Hi,I have an interesting issue in terms of caller-ID using a Cisco UCM 8 and a voice gateway.Before we were using CCM 4.3 with a Cisco 2800 for the Voice Gateway via MGCP.We moved to CUCM8 with the same voice gateway via MGCP.Everything works, but th...
Hello EverybodyI need a help with regard to the following:I have one EM-HDA-6FXO module installed on router Cisco 2951, and i need to establish power-fail connections in an emergency. The question is, how many analog phones can i connect on this modu...
