Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
How can you check the heat (temperature) of a MCS-7825 (HP-based). We suspect maybe some issues with overheated equipment. Tried looking in the RMTP but found nothing there. Is there a command via SSH maybe?
i have a customer ( Hotel )need to make any calls between the guest rooms hide the caller ID and in the same time if the geust calls the Reception the calls run normal and the caller ID appears . all the guest numbers begine with 7 or 8 .any one can ...
We had a working phone system with a t-Com box from Deutsche Telekom and we are installing a new Cisco 2921 CME configuration. We can get in coming calls but we can't make outside calls. The call is getting to the telco and then being dropped. I have...
Hello,is it possible for an user to lock his IP Phone, so that other users can't use it while he is away from his desk?It should be a password, or access code, but it can't be extension mobility.What can you suggest to me?Thanks and regards.
Dear AllI would really appreciate it if someone could help me out with this issue, so thanking you guys in advance. I have two CUCM clusters and both of them generate the same error while taking backup " TAR FILE NOT CREATED" and the backup fails on ...
Hi All,I am having trouble getting calls in/out of an H323 gateway connected to a partial ISDN service.I have attached a debug and a router config.If someone can have a look and see if they see anything drastically wrong, that would be most appreciat...
Hi all,For what i could understand from the admin guide, to access services such as EM on 6921s, you should press the applications button and then services.But in my case there is no services option.Other phones are working correctly with EM.Whta can...
Morning all, I'm stuck on a problem that I can not find a way around at the moment without editing every user profile.We have CUCM 7 working which integrated into our AD so all end users are already associated with CCUM, I need to set up 90 users wit...
I have this translation-rule configured:voice translation-rule 3 rule 1 /900\(.*\)/ /1#\1/then a translation-profilevoice translation-profile TO_GK translate called 3and a dial-peer to direct the incoming call to Gatekeeper by translating the outgoin...
Hi,I have a CUCM BE 7.1.5. I need the board number of the DID to be used for AA in Unity Connection.At Same time this number will be used as the extension number for the operator. ie same number will be used for different end points considering th...
Hello,Im reading about the steps necesary for do the upgrade from 4.X to 8.x with remplace hardware. After read for all day I not get nothing clear, so I just write the steps I think I have to do, please correct me.Check all before start upgrade1) Ch...
Hi there,I am planning an upgrade for Pub & Sub from CUCM 7.1.3 to 8.0.3 since we want to go virtualization.The 8.0.3 will be virtualized on UCS server with ESXi installed. Right now the Pub is on MCS 7825-H2 with 2GB RAM and 76GB HD with two partiti...
Ok ladies and gents - this is a strange one.We have just bought a 7921G wireless phone for our second small office.We have a CME 4.2 running with about 20 phones. I also ran debug tftp packets when this phone registers and have placed on the CME all ...
Hello, I’m fairly new to CUCM and I can’t seem to pin point a fix for this issue. Every time I try to re-redial a missed external call, the 9+1 is not placed within the redial and the re-dial call fails. I tried to look within CUCM but can’t seem to ...
I have a problem wiht a cisco ip phone, 7921g, which cannot boot up normally. In other words, I can only see the Cisco logo on the screen and the green light flashing quickly.Is there any way I can hard reset the phone by giving a combination of keys...
