Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
hi Team, I am trying to test a new feature of CUCM12 (extension mobility roaming across cluster) I've ILS setup between clusters and I am able to advertise patterns over ILS (GDPR). I have configured 1 end user each in both test clusters and both...
Below is the current config Call comes in, goes to 2000 (auto-attendant UCCX trigger in CUCM) When CUCM is down, 2000 doesnt exti, calls go to 2339 and if no answer to 2340 under SRST mode All of this works Now, if I replace 2340 with a mobile nu...
I have 2 sip trunk circuit at 2 different locations for failover. Is it possible to add another sip circuit to one of those locations? Also do I just need to add additional dial peers for the new sip circuit ?
Dear All, I have a multi forest enviroment Basically a lot of Domain each one with the personal AD + DNS I'm following this guide to configure the LDShttps://www.cisco.com/c/en/us/support/docs/voice-unified-communications/unified-communications-m...
Hi, I will need to patch esxi on the publisher, subs are patched already. Do i need to restart subs after PUB patching complete and I power it up ? As I understand when I shutdown PUB I dont need to touch subs, correct ? thank you
i have a specific number that cant call through a trunk to another avaya telephony system in australia, my system is a publisher and a subscriber cucm 10.5.2 , all other lines can call through the trunk to the telephones , when i ran RTMT it gave me ...
I have a CCM 8.6 cluster, I can't pull logs via RTMT from the any server, I get the following message when try to run remote browse (or collect files or realtime trace) "" Could not connect to server <hostname> . Please check and correct following:a....
I don't believe there is a way a user can remotely log out of EM, but I thought I'd check with the community. The only alternatives I see are having someone at the site log off for the user, or call our help desk to have the logoff completed via sys...
A client is using 10.X CUCM and is wanting to know the credentials of the cisco ldap account we created in AD. We seem to have set it and left it alone for some time. My question is: if i update the password in the GUI (and they update the password...
Hi, Kindly we have 3 UCS servers and will configure them as a VSAN cluster Is CUCM installation is supported by Cisco on Vsan and there is no problem with that ? We already installed CUCM on SAN and also on local disk and both were supported ...
Our Client has several 6945 phones that will not register to the CUCM version 10.5. Few thing we tried. Factory reset the phone. Phone will note register to CUCM even after the reset. Phones were in CUCM before and were put in closet couple months ba...
I'm having a problem with the labels showing on the phone, but not on the expansion units. I have a phone with 1 normal line and the rest of the lines monitored. ephone 47 mac-address 381C.xxxx.xxxx ephone-template 3 type 7975 addon 1 7916-2...
Outgoing Call has no Issue,However if we call our PSTN # connected to FXO port, It will ring 4times only then disconnect then we hear a pulse tone(not a busy tone). If we answer the call before the 4rings we can talk with no issue. below are our te...
Hi guys!! I have a CUCM 10.5.2 configured on my customer, they have a integration via H323 with gateway Alcatel system. In CUCM I have gateway H323 configuration to Alcatel. Happens that a call from IP phones Cisco to phones on Alcatel don't have ...
Sorry for the confusing title, but i have a problem : My boss want to evaluate which pstn numbers are not used and want to drop those numbers for efficiency. So here is the our voice design : We have 1 voice gateway with E1s for telephone and FXOs ...
