Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hi , I have facing some problem for IP Telephony system. When I have call from outside on IP Telephony system like "+8809610127777" then DTMF and IVR tone working fine But after I have dial extension number like "520" but call not transfer this exte...
I would like to add a new sip trunk - "test" to an existing SIP GW for testing. The GW already has some production SIP Trunks connected but I need to create a new one to testing some settings which would involve resetting it The existing SIP trunks ...
Hi All, I want to understand that when never we apply a new background image to 79XX, 88XX, 89XX, 99XX cisco phone and restart the TFTP server and restart the phone and if the phones are logged i by extension mobility profile will it take effect or ...
Hi, I was testing Cisco Unified Mobility Single Number Reach on a new CUCM Cluster. When I dial the deskphone with mobility feature enabled, the remote device rings but the moment I pick up the call, the call drops. If I don't pick up the call after...
Hi guys, I've configured a hotdial extension on my Call Manager, as soon as the phone goes off-hook, it dials a pre-configured number. However that number is private and I would like to know if there is a way to hide the number that is dialed, since...
Good day!! One question .. I have five extensions 7100 --> ... 7104, I need that if one extension not answer after 10 seconds, anyone the others extensions can answer the call !! What I need to configure ?? Hunt List?? Thanks..
We use IP communicator on a few PC's in our Company. On those PC's we also use DeepFreeze to mitigate any viruses or issues with the PC since they are at remote offices and are not on our domain. The users use a VPN to connect. After a reboot all of ...
Hello I'm working in a Dial Plan design but the used of route filter is require from mark local calls and long distance calls, but the route filter architecture is kind of complicated, there's a way for used Globalized Dial Plan for avoiding using R...
We have a smaller site we support with an aging call manager, recently a new firewall was installed which caused some issues. At this time however we can talk to the networks, all IPs ping each other but we cannot get the GUI to load for CME or CUE. ...
Hello All, CallManager: v8.6.2.24901-1 I was wondering when a Directory Number is part of a Line Group, when is that DN considered to be idle or unavailable..? I've been doing a little testing with a Hunt Pilot-->Hunt List-->Line Group, using the ...
Hello All, I has been updated a cluster from 6.1x to 9.1.x, after doing MGCP gateway working fine technically but the gateway page shows IP Address "unknown" , i am not sure either it is a bug or any cosmetic issue. I am attaching the snapshots as...
Dears, we are facing issue in our network, when we call from IP Phone to Mobile or landline number its disconnect automatically after 12 minutes. what I need to check in configurations.
Dears, please describe this SIP Profile,sip-ua retry invite 3 retry notify 6 retry register 10 timers connect 1000 timers notify 100 registrar ipv4:192.168.126.1 expires 3600 sip-server ipv4:192.168.126.1 notify telephone-event max-duration 200 host...
Hello, I'm facing issue in outgoing calls, incomming calls working fine. Outgoing calls choose correct dial-peer and interface but ITSP don't receive any call on that SIP Trunk. They receive a call from another SIP Trunk that's terminate on same VG....
Can Anyone answer my below question? 1 How many call can handle by CVP PIM in comprehensive model? 2 In comprehensive model without SIP proxy server is possible to do load balancing? If so How we can implement it? 3 If one call get drop in between ...
