How do I change the default persons name after you enter the password to the vm? I've reassigned Bob Smith to Jim Smith's vm box which he no longer uses because he was termed. When Bob Smith hits the messages button and enters his password it immedia...
Hello all, Quick issue I am running into. I set up a hunt group yesterday for a small clinic and rather than having the same DN on every phone I simply created a hunt group as they wanted some phones to start ringing after other phones had started ...
Hello, I am having an issue with a Call Handler. I setup Caller input key "0" to "Transfer to alt contact #" which is the front desk ext. When you press 0 during greeting, the system prompts " wait while i xfer call" then silence for roughly 10 seco...
Good day!! I have one cluster CUCM version 11 but only in the node publisher appear the next error "DNS UNRECHEABLE" (Image 1), I revised the configuration in two nodes is similar Image 2, but I don´t know the reason this error. Thanks for your time...
Hello We are having a Site A where BRI are configured on the Cisco router...there ar some DID numbers are free... Now we are planning for build up the new Site B with the WAN connectivity with Site A....& planning to configure the Free DID numbers ...
Short description:I can not install cop firmware phone 9.3(4) (cmterm-8941_8945-sccp.9-3-4-17.cop.sgn) on CUCM 11(0)1.During SFTP installing I got error : Error encountered: The selected file is not valid. Please ensure that the COP/ISO file is inte...
Hi I need to disable Default Voicemail user greeting in Unity Connection "Sorry <name> is not available", Instead of this I need to play user extension, Please help me to do this ? Bit urgent... Regds $
Dear All, I am facing the problem where my Cisco 6941 phone doesn't know anything on screen after i did the factor reset. It is just showing Phone Not registered. "Big Concern is that i cannot press any key on phone after this". Anyone faced this...
Hi All, We integrated a GSM Gateway to the Call Manager and added this for the existing Mobile Voice Access setup. During our testing, there was an issue when calling the Mobile Voice Access feature. As per checking by the GSM Gateway personnel, he ...
Hi, I have configured and registered transcoder which is needed for transcoding g711alaw (only codec supported by ITSP) to g711ulaw (IVR). When IVR number is called ITSP sends INVITE with G.711 PCMA in in SDP part. CME replies with OK message, G.711 ...
Dear forum users. I have a client with the following:- CUCM System version: 6 Firmware:SCCP11.8-4-2Sphone model :7911Phone number : 1067The client is complaing of call drops , internal or external it doesn't matter and the time varies, can be 20 se...
I have a call manager in China . It manage two voice gateways， VGA and VGB with H323. and I configured a SIP Trunk to a SIEMENS VoIP PBX in Sweden. The SIP Trunk enable "OPTIONS ping" to monitor destination status . I created a Route Group that incl...
Hello All, How can I see who is attending Meet Me conference? Any way to see?
This is a basic question for most of you guys but I need some confirmation of call routing process. I am needing to include a couple new test DIDs into our system for a new circuit. We are receiving 3 digits from the carrier. I already have a dial-pe...
Hi, One of our client is asking if there is possibility that we can use Pin code during SRST mode.I think FAC only use for CUCM only, please correct me if I'm wrong. They used Cisco 3925 with IOS version 15.4M1. Thanks, Gritzen
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 12-31-2025 01:52 PM | ||
| 12-10-2025 11:24 AM | ||
| 11-16-2025 10:18 PM | ||
| 10-15-2025 09:15 AM | ||
| 09-26-2025 02:09 AM |
