Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Dear all i have a question about Cisco Unity Connection, can i make multiple IVR in Unity connection for different times of the day, lets suppose form 9am to 5 pm different greetings and 5 pm to 1 am different greetings etc ?? em using it as when cal...
Dears,It might be very silly nd stupid for asking this question but it has been asked to me. How i can pull the configs of complete CUCM ------------Is it the backup of CUCM will help??? and in which application we can open the backup filesHow i can...
Hi All, I have an office where the D channel on one of the PRI's is down and when I run the show ISDN Status I get the following output:ISDN Serial0/1/0:23 interface dsl 2, interface ISDN Switchtype = primary-ni L2 Protocol = Q.921 0x00...
Hi, Got below para from one of the Cisco document, does seems' contradictory? -------------------------------------------------------------------------------------------------- Special Note on POTS Calls with Empty Calling Number Field Assume this co...
Hi Friends, We have a strange issue in our Ip telephony network.all users in a call face 3-4 seconds of Audio Loss.even between extention to extention.No config have changed ,Switch interface and Voice router (2851) CME.7.0 with phone loads 8-4-2SAll...
Hello Everyone,I'm having an issue trying to get a Polycom Soundstation 7000 IP to register with my CUCM. Here are the bullet points:-I've followed the Polycom guide for registration-I've spent 40 minutes on the phone with Polycom support, with no lu...
Running CUCM and UC 10.5. My message store is internal to UC. I'm trying to set up message notifications to email.I've configured my SMTP SmartHost, and for a test user, enabled a Notification Device (SMTP). But I never receive a message.Am I mis...
Hi all,I've an issue about Speed Dials on ip phone 3905.here seems that speed dials are supported by 3905.http://www.cisco.com/c/en/us/td/docs/voice_ip_comm/cuipph/3905/10_0/english/user_guide/IP05_BK_U2FC56CE_00_user-guide-3905_10_0/IP05_BK_U2FC56CE...
Customer has a virtual CUCM, CUC & CUP environment running on 2 hosts in the same chassis. CUC & CUP are misbehaving due to known CPU utilization bugs and will be upgraded to latest SU. Question is what to upgrade first? CUC is the most unstable,...
Hi,I have a line with extension 1001. CFA, CFB and CFNA for this line are set.I need to accomplish following task: When extension 1002 dials 1001, all forwarding settings must be ignored and call must not leave ext. 1001, when any other extension cal...
Tenemos una central 2921 y telefonos 3905, cambie la hora en la central y me gustaría saber si hay alguna manera de realizar un reset a dichos teléfonos para que actualicen esa hora, sin necesidad de ir a cada uno de los telefonos a desconectarlos y ...
Hi, Currently we are working on remote side, facing issue in incoming DID calls. I have tested translation patterns and dial-peer in existing cme scenario, its working fine but when i tested with cucm it gives me following error. But same configurati...
Hello All, we just recieved the CP-7945 phones.one of the phone on connecting is trying to upgrade the firmware.the current firmware on the phone is 9-3-1.the latest which i can download from cisco website is 9-2-1 which will not work in my case. so ...
Hello, does someone know if it´s possible to restrict a phone in a way, that the CFwdAll function is not available for a specific DN button? In the below example the user should be able to use CFwdAll just for the button 1:3, but not for 2:12. How ca...
Hello All, I have a customer who recently changed out their key system and has a new voip system in place. They have asked if it is possible to map phone line buttons to the two analog trunks they were once using on the old key system. These analog t...
