Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
After configuring sip trunk my cp 9971 sip phones won't register with the error below: Jan 10 12:23:45.420: //33/FD5F39A5801D/SIP/Msg/ccsipDisplayMsg:Sent:SIP/2.0 401 UnauthorizedVia: SIP/2.0/UDP 172.16.90.137:5060;branch=z9hG4bK6a527bfcFrom: <sip:10...
Dear All, I have a unique issue, where if agent received call through UCCX, call log is not appear in phone directories. But, if direct call from user to agent extension, call log is appear in phone directories.note: agent using CP-7960G When an agen...
Hi, I am trying to import a local address book via the web interface of a 210 base station, but I always get an error.Reproduction:Login in Basestationswitch to "User" pageExecute function "Choose fileSelect fileExecute "Load" functionExpected result...
I have a PRI connected to my router and was asked to have a analog phone work from off the router bypassing call manager I am able to see call coming in with a called party number '1234567899' but debug states the call is Unallocated/unassignedmy dia...
Hi everyone, Our few ip phones are not getting registered on CUCM, it's a seperate office. Intermittently the phones are getting registered after a reebot. After a while it will unregistered from the server.Can any one please suggest me some trouble...
I'm configuring CUBE HA on 4461 routers. Smart licensing is enabled and authorized. Cube status is showing good PHC-COLO-ISR-02#sh cube statusCUBE-Version : 12.7.0SW-Version : 16.12.3, Platform ISR4461/K9HA-Type : noneLicensed-Capacity : 400Calls blo...
Hello,In our infrastructure we have our 8841 desk phones registering to our Subscriber(Primary/Active server) and as our 'Stand-by Server', the Publisher(Secondary server). I also noticed that the TFTP fields correlate this as well in the phone IPv4 ...
Hi GuysCan anyone tell me what the below commands are for?This is a CME with SIP to the ISP.Does each phone have to authentication when making a call out?This is the config for the provider on the CME, can someone explain what each is for? sip-uacred...
Hello all, recently when deploying MGCP gateways we have found that after upgrading call manager to version 11 when we configure the "ccm-manager redundant-host" & "mgcp call-agent" are changed from ip addresses to FQDN as soon as the gateway reaches...
I'm new to working with call manager software, my agency using cucm 10.5.2 still (upgrade coming soon...). I've been looking at RTMT can can see how many calls are active on our PRI, is there another report in RTMT, or maybe CUIC that'll tell me wha...
Hi all, Is there a way of displaying when a phone has logged in and out of a hunt group? The only way that has come to mind is on the logs of the phone. I have http onto the IP address of the phone and I have collected the console logs, will the cons...
Hi, We have configured a Paging overhead using a FXS port to sent the signal to a Viking device with the following configuration:voice-port 0/1/1signal groundStartstation-id number 201caller-id enable!dial-peer voice 201 potsdestination-pattern 201po...
Hello,I have come across a scenario and would like to have some opinion to fix this;- Team currently has a webexcc queue.- They dun want that queue anymore and would like that number to directly go to a voicemail where the caller can leave the detail...
Hi Team, I would like to know how to work on filters while debugging SIP calls. e.g. i get ton of calls on my Cisco CUBE. From multiples sites. I can differentiate sites with IP Address (remote CUBES) or from particular range of caller IDs (FROM)? ...
Hi i have an 8961 registered to CME 11.6 i have configured BLF speed dials and these work as they should . if i want to transfer a call i hit transfer it opens the new call window if i press one of my blf speed dial buttons it creates a second indep...
