Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hi everybody.Let say we have a cucm . We already have added phones manually or auto to our CUCM. After a few weeks, we want to restore our CUCM to defaults i.e no record of any phones etc. How do we do that ?Thanks and have a great day.
Dear Support, As we have Two cisco 3900 series VG(H.323) connected two E1 lines on Each VG and aslo 12x2 PSTN lines fxo as backup lines . in case E1 disconnect user can dial out via pstn lines as backup line connection type fxo .Main company teleph...
Hi,We have 2 remote sites that have both a connection to the datacenter where the CUCM and some media resources are located. There is no direct connection between those sites.We would like to allow the two sites to make calls between each other and a...
Hello Friends,I´m enabling T38 fallback cisco, but 2921 says invalid input.Can you help me please?Router2921(config)#voice service voipRouter2921(conf-voi-serv)#$l t38 ls-redundancy 0 hs-redundancy 0 fallback ciscofax protocol t38 ls-redundancy 0 hs-...
Hi everybody.Suppose we have a CUCM running tftp. We have 7940 phones registered with cucm.All our phones are running same firmware. During boot up, phones request config file from tftp(CUCM in our case). This configuration file contains among others...
hi everyone when i transfer a call from PSNT to another PRI (the PRI is goto siemens） the gateway will TX a disconct message Recovery on timer expiry the time always 19 secound'the gateway is a h323 gateway with CUCMthe log is debug cch323 and the I...
Hello,I want to know which card do I need to connect my VG 2951 router /UCM 7.0 to Alcatel PabxI've been told that they need E1 with signaling qsig+available cards:HWIC-1CE1T1-PRIVWIC-2MFT-E1 NM-HDVwhich one will be betterregards,
Dear All,I am running call manager 9.1Is there a way i can track which ext is calling where and the time duration.Kindly let me know if this option is available in call manager 9.1Will be very thankful for your support.Regards,Malik.
Hello,we have a CUCM that uses a Cisco 2951 with IOS c2951-universalk9-mz.SPA.153-1.T.bin as a Voice Gateway (in SIP).We have noticed on the router (by the command "debug isdn q921") that the messages in attachment appears continuously.Here's a sampl...
Dear All,I am running call manager 9.1I have a question that when you want to make a call to any other internal ip phone user for example you press the first two digits of the other extension the i phones displays the extensions in the drop down list...
Hi everybodyPlease consider the following scenario:Let say I want to upgrade my 7940 FW. My CUCM is also running tftp service.Suppose we already downloaded latest FW in our root ftp directory on a computer. This computer and CUCM are connected to sa...
Hi everybody1)Let say we have a cucm running tftp. Our tftp has two files for our 7940 phone.00308005000030800600 ( I just made it up)Currently the configuration on tftp contains load pointing to 0030800600.Just for some weird reson, we want the load...
Hi,I've been wondering if there is a better way to check the status of a SIP Trunk being up or down since the status of it does not show up on the Trunk in CUCM. I have been doing SDI trace to check that there is communication on that SIP Trunk and ...
Dear Experts,1) I would like to Add '0' to an 10 digit incoming call because i am getting only 9 digits from the SP on AnalogLine terminated on FXO using H323 Protocol with CUCM 8.5 this line is dedicated to the manager for both incoming and outgoing...
Hi everybodyA video lecture says we can have upto 8 cucm per clusterDoes it mean we can have upto 8 CUCM in addition to a publisher which is not running any CUCM service?thanks and have a great weekend.
