Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hi,About to integrate CUCM 7.1 and Unity connection 7.1 with LDAP / AD.The userids in AD and Cisco don't match. Changing the AD Userids is out of the question for obvious reasons.So before starting the LDAP process I would like to change all userids...
Hi,I have ATA 187 running with CUCM 7.1.5....I can receive FAX without any issue, but unable to send FAX at all....Why that so?? Is that a bug with ATA 187?? Can someone guide me...
Hi,Running CallManager Express 7.x.E1 PRI pilot number is 42345200 and the DID range is 42345201 to 42345299.The Service provider is sending last 3 digits i.e., 2xx.IP Phones are configured with the DN's starting fron 201 to 299.If we try to reach th...
OK, I have a question, that I am sure somebody has already ask, but thought I would ask as well.Is there any way to combine all the different system views of RTMT into a single instance. I am running CUCM 8.5.1, Uconn 8.5.1, Presence 8.5.3 and UCCX 8...
My network has many different flavors of DSPs in it, pvdm2-xx and pvdm3-xx. I'm confused how to manage those DSPs for conferencing since each of the on board DSPs support various numbers of callers into conferences.I'd like to be abe to say this...m...
How can you list the DSP modules in a gateway without opening up the box ?GTG
Hi,In CUE script editor, I want to have the possibility to press 9 for french instruction.I have 3 idea but not sure ( I'm an IPCC guy )1)I saw some people that did a link from a script to another with the 9. So if you hit 9 it will redirect to a Fre...
PSTN -(SIP Trunks)->VGW3845 -(SIP dial-peer)-> CUCM 8.0 --> Unity call handler --> CUCM route pattern -SIP Trunk-> same VGW3845 --> fax server. once the user dial the fax extension i can't hear the fax tone however if i forward the call from the VG...
Hi,Would like to know is there way to able press call-forward to a system handler programmed number ?I tried on call forward that but it goes to the generic unity voice annoucement. How to do that ?Thanks
we have brand new CUCM 8.5 and brnad new 6961 ip phones. Configured all without problems, connecting phones and they get the rigth firmware which is SCCP69xx.9-1-1-0.zz.CUCM administration page says the phone is registered, but the phone display say ...
Experts,I am facing error code 10021 when exporting CDR report from CUCM 6.1.2. AQfter searching on Cisco site, i found the below linkhttp://www.cisco.com/en/US/products/sw/voicesw/ps556/products_tech_note09186a0080933fcf.shtml#Problem2i did that sol...
Hello all,im trying to make a call queue so if the all the agents is occupied they will hear a message saying all agets are busy please hold or press 9 to leave a voicemail. Everything is working exept the press 9 to leave a voicenmail. When i try an...
Hello All,I have AIM-CUE version 8.0.2I want to check with you guys if anyone has custom script which says "Welcome and then press 1 for Nick, 2 for Dean or press 0 for operator.If anyone has basic script like this,it would be helpful.Please let me k...
Hello to allmy voip network is as attachment pic.so i want to use fax on my network, and for using that i install 1 VG-224-FXS on my networki config vg224 as MGCP gateway,so i can call numbers in CUCM and can recieve fx from outside of the companythe...
Hello,I have a problem:my Panasonic TDE200 is configured and works good with softphones. But I can`t configure CISCO 7911g - it successfully gets xml files from tftp server, but doesn`t send REGISTER request, instead it sends INVITE.I had read a lot ...
