Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Dear NetPro gurus,I have 3 questions and would greatly appreciatied your assistance on this.i) What's the main benefits / difference between Cisco 3945 Vs Cisco 3945E ISRs?ii) With the Cisco 3945 router, what's the maximum number of E1 ports ...
Good Day All,Does anyone know of any documentation on getting the 6921 Cisco phones (SIP image) to work with a third party PBX (based on trixbox).Any information is most appreciated.Regards,Amanda Lalli-Cafini
Hi, Due to some issues with our license we were given a temp 3 month node license to activate 3 nodes in our 5 node cluster. We have now received and loaded the correct permanent licenses, but the temp license is still in use and we have a total of ...
Hi,I can´t change the logo Cisco 7912 in the CME. I´ve following the configuration guide about documentation step convert the logo, to create the configuration file, to uploaded files available to the IP phones using the commands tftp-server flash, b...
I am exploring forwarding a number and have been told by our provider that there will still be half a ring that comes through before it forwards. I attempted to set the ring setting on the line in CCM to "disabled", but it still rings. I'm not sure...
Error is: ReqLine IP addr does not match with host IP addr Invalid URL in incoming invite The sip invite is received with an@and the router seems unable to make the translation from the public IP to the CME at private 192.168.1.x The error can only b...
I have ASA 5510 appliance with 8.2.4 IOS, we implement voip between outside and inside interfaces, the connection betwen two ip phones drops after 30 sec.
Hi ,Two of our customers reported similar issues, they're having unauthorized IDD calls reflected in their Telco billing. I can't see any records in the CUCM cdr, the only traces of the calls was found on the PSTN gateway (seems like a loop);0x2B704 ...
Is ESXi Version 4.1 Update 1 supported for CUCM, Unity Connection, UCCX and Presence?Thanks,Doug
I have outbound SIP calls comming in over a sip trunk.. Some users just have a sip address and others have an extention defined.I have a translation pattern that attaches a specific phone number to calls headed to the PSTN, I know that both calls fr...
Hi~ AllLong time no post~i have some problem about Localeim down load Kr locale and upload CUCM but 6921 only work english(default)But 9951 was working Korean(Kr locale)so i dont know why happen to this.i attached file .ppt and you can see the some i...
Hi there,As the topic says I have a difference of 10 min between the real time and what it is on my phone. It's the same time for all model, and my firmware is 8.1.1 on CUCM 8.5.1. Anyway, it is not a firmware problem because if I : utils ntp status...
Hi,our company has a 7905 that cannot be used, I cannot find out it in CUCM, I feel it must be a sip phone, I used **2 to restore it to factory,but when it restart, it keep "SIP" states yet! I want use sccp for it. who can help me , thank you so much...
Hi everyone,We are getting SNMP alarms on Spectrum from 2x MGCP gateways. They are both 2811s running IOS 12.4-24.T5. Both Gateways are connected to PSTN via ISDN PRI.The alarm name is "POOR QUALITY OF VOICE NOTIFICATION" (see screenshot attached). I...
Hi,I am assuming, but have not found any documentation specificially talking about mixing the types of servers in a single CUCM cluster. We are running 7.1(5) currently. I can't imagine this would cause any problems as long as they can support the ...
