Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
In CUCM 8.0 I know I go to the Operating System Administratrion and click on software upgrades which gives me two options Install/Upgrade or TFTP File Managment. Which one of these do I use? I think it is Install/Upgrade. Also, do I upload the .cop t...
OK, I have a question, that i am hoping someone can provide some information on.Currently I am running CUCM 7.1.3, CUPS 8.04, UCCX 7.01 and Unity 5.0. When CUPS 8.02 was released it only required CUCM 7.1.3, but now it is 7.1.5.If I upgrade from 7.1....
I am trying to get Xlite version 4 workinmg woth callmanager 7.1.5, all i get is 408 error. I have associated the device with the line, Has anyone done this with version & of callmanager
We are running CUCMBE 7.1.3 and have multiple buildings. One PSTN connection so we are implementing a 3rd party E911 solution. The problem is that we have a handful of DNs that are in different bldgs using the same dn/partition. They require this DN ...
Hi,I think I already know the answer is no! But can anyone tell me for definite whether call manager will collect CDR information about a call coming in from the PSTN, through a h.323 controlled voice gateway, to an extension in call manager, when th...
Think I may have posted this in the wrong place before.System version: 7.1.3.30000-1 Trying to add the 8961 and 9971 phones. Have uploaded the default phone loads, but they are not showing up. Am I missing something?
Hi All,Can I use Hunt Statistics without configuring B-ACD.hunt-group report url prefix tftp://10.1.1.15/CMEData/datahunt-group report url suffix 0 to 23hunt-group report every 1 hoursWill the report send to tftp server for normal hunt Pilot ?Regards...
Hi all,I've got the audio source file uploaded and ready to go. I would like to find out where would be the best place to apply the MOH audio source to all devices. I am looking at the "Common Device Configuration" page. Would that be the best place ...
Hello All,Here’s what we have: About 250 APs and 300 wireless phones in 5 different buildings within a campus. Let's say the AP’s are in the 10.83.28.0 range and the wireless phones in 10.10.44.0 with following restrictions: 1) We can’t associat...
Greetings,I am running some polycom phones through a Cisco 860 router (no CCME/SRST stuff). Just a plain jane router, and it works fine, in fact any router I've tried, except the 851 works fine.If I try and run the same phones through a Cisco 851 ro...
Hi,in my CUCM 7.1.3 publisher i have configured a bunch of phones to a pickup group and set also to visual notification.I have also configured that timer to 1sec so whenever a call rings one extension, each one of the group knows that a phone is ring...
Hello to all.I would like to ask you, how can I disable the Message Waiting Indicator in IP-Phone (Cisco Call Manager 6)?Thank you vey much.Isidoros A.
HiI am facing a issue , I have a setup with cucm 7.0 and presence 7.0In my cupc the sofphone is red other like deskphone etc are green and working fine(show server health )Softphone is not working and UPC<userid> is unregistered in cucm.I have checke...
I know that the period (.), represents any digit. Recently i came over a config wherethe dial-peer looked like this:dial-peer voice 100 voip huntstop preference 1 destination-pattern .. session protocol sipv2...The destination-pattern is defined by t...
Hello,I am looking to upgrade my Unity 5.0 server to Unity 7.0. I am also upgrading my partner Exchange server from 2003 to 2010. I will have both Exchange servers running side by side for about a month. What steps do I need to follow for the Unit...
