Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hey i dont use ATA's much, except for faxing. However today i had to deploy one for a client and it failed miserably with horrible call quality. I was wondering if anyone knew why. First piece of evidence is that my ping time across the lan to these ...
Hi all, if I understood correct, I should be able to set "do not disturb" on Jabber and the associated device should also go in the "do not disturb" state and vice versa?! If it should go, there is a bug? UCM/IMP 11.5(1)SU4, Jabber4Win/-Android/-iP...
I'm hoping someone can explain or point me to a clear description of the 4300 ISRG3 CUBE/SIP licensing.
Hello all,May someone advice me how to configure trunk without credentials and authentication section?Topology:CME---Mikrotik_router----trunk----ITSP(two vlan Internet+Voice) For peering with IP what Configuration should I do under sip-ua in order fo...
Hi I have updated the List.xml file in the correct folder and uploaded the images.Restarted TFTP servers.I was able to successfully view and set the image on one phone.Rest of the same model phones does not show the new images. It shows default image...
Hello peopleI am pretty new to the community so hello there :-)I am setting up the Cisco Jabber on the computer in domainI am receiving the message "Your username or password is incorrect"I have checked the login name via https://<CUCM IP>:8443/cucm-...
Hi Experts, My customer wants to move VMs (CUCM, CUC, IM&P, UCCX) from the existing host Cisco UCSC240-M3S (which is EoL) to a new ESXi host.Is there any cisco page available (could not find so far...), where steps are listed and explained what and h...
HiWe have CUCM 11.5. I have problem while generating CDR report on CUCM. I can generate report from CDR==> Export CDR/CMR on CUCM.But I can't have the reports of: System Reports ==> QOS ==> Detail and the error code 10011 occurs. The error is atta...
Hello CSC Problem DescriptionI have a C2811 GW with c2800nm-adventerprisek9-mz.151-4.M12a.bin and one VIC2-4FXO connected to a legacy 4xSIMs GSM GW for outbound calls to cel numbers. Each GSM GW FXS port is a SIM card, and each one is connected to a ...
Hello experts -This is almost embarrassing to ask, but here goes anyway!Do new 8800 series phones (specifically 8811s and 8851s) come with the phone sticker-labels for the headset, hold, mute, etc buttons?I have found a 3rd party that sells the stick...
We have UCM 10.5, MOH stopped working for inbound calls where it works for outbound calls.All the media resources and MOH configurations looks ok
So long story short, despite the following bug ID saying that the Catalyst 2960-L switches are supported as of various versions, most of them are actually NOT supported still despite the BugID being marked as fixed. https://bst.cloudapps.cisco.com/bu...
Hello,I have few question about SIP trunks in general and wondering if some of these scenarios are possible to execute.We have a customer with branches dispersed all over the place and DR sites.We have two ingress SIP points one in HQ and one in DR. ...
I was implementing a SIP trunk from Verizon for a customer and I was skimming through the document specific for Verzion and CUBE on ISR 4K series and I realized on the CUBE it says early-offer forced but the trunk from CUCM to CUBE has the SIP profil...
I have SCCP894x.9-4-2SR3-1 loaded on my phone and want to change it to SIP894x.9-4-2SR3-1 but I must be missing a step. I am running CME 12 on a 2911 router. Before I start with my config, how easy is it to have both SCCP and SIP versions of the sa...
