Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Dear Allwe have an issue with fxo portsour deployment isCUCM ----H.323 GW with FXOOutgoing calls works fine ,but no incoming calls success .This Gateway in Tanzaniakindly find attached run config and debug commands
We recently upgraded to CUCM 11, which added the "home cluster" options on the end user page. In our environment, all users are LDAP synchronized and we filter the users that are imported, so only our own region is synchronized and all of the importe...
In CUCM 8.6+ how long does the audit log remain before its overwritten? Can this be changed in Enterprise parameters? I know you can grab them in RTMT but wasn't sure of the retention period. Thanks,
Hi- facing this challenge with translation patterns. Our company has 3 locations and we use 3 digit dialing for 2 of them now. Issue is, we are over 1000+ numbers. Is there any way to accommodate this many translation patterns with this amount of num...
Hi,Miscellaneous signaling debug data: (ch=1). When i start the router my voice card showing green light stable and not getting the dial tone. Kindly suggest how can i fix this issue.
Very odd request. Customer needs MRA to Internet as normal spanning over firewalls. But security is setup so that no workstations can communicate to any other workstation. So point-to-point traffic such as audio/video, screen share, file transfer,...
Sirs I have been given a bit of a challenge by the business. We have a Cisco UC solution running v 11.0.1.21900-11 Handsets are CP-7821 We have one handset that is set to forward to a mobile phone for a very specific out of hours service. The proble...
HI guys, (CIPC version 8-6-4-0) (CUCM version 10.5) My TAC contact is off-shift but he told me to gather the Console Logs for a CIPC that I am having issues with. Where do I do that? On a deskphone, it's found on the phone's IP Page. But CIPC I...
Hi, I have the following setup. SIP trunk Provider --> Cube --> SIP trunk to CUCM. We are having a special dial pattern to dial outside. *9*external_number. The *9* is removed on the outgoing dial leg of the CUBE. When I make a call from my IP com...
We are running into this bug: https://bst.cloudapps.cisco.com/bugsearch/bug/cscuj22395 ) We cannot find a workaround, and Cisco has not yet responded to our escalations through TAC and AE. Any ideas on other Border Controllers that we could use unt...
I have 2 PRIs that we are getting random long distance failures on outbound calls. These calls result in 1 ring and then a message stating "Thanks for choosing so and so for your long distance needs." and then going to fast busy before disconnecting...
Hi All, Need your help to understand the CUCM cluster sizing. The maximum number of nodes allowed in a cluster are 21. Out of which how many can be subscriber and for what purpose we can use them. out of 21 we can use 1 Pub node 2 TFTP node and 2 Mu...
Good morning, I'm trying to configure the SRST for sip phones. I've configured srst on CUCM side, and the following there is a configuration on the router: !voice class codec 1 codec preference 1 g711ulaw codec preference 2 g711alaw codec preference...
When we dial outside mobile numbers then two behaviours have been observed for few mobile numbers: when the call is getting tried there is a dead air for few seconds, after this the calling number is changed to last four digits of the dialled numb...
Hi All, the consultant who initially configured our CUBE router had this dialpeer responsible for handling the cases where a phone dials a 3 digit telco services number (should include 911, no other dialpeer matches it in our config) dial-peer voice ...
