Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hi,There are two user groups: Managers and Personnel. Only Managers group can call mobile phone numbers: 98... .......In every ephone-dn there is a "call-forward noan 98XXX XXXXXXX" entry where XXX XXXXXXX is the mobile phone numberof a particular us...
The CUCME System Admin Guide explains how to configure the CUCME, but does not explain the “why” these configuration commands are needed. I have gone through the “Configuring Conferencing” chapter several times – and am still with questions. Spec...
Hi,I have just been provided a new voice line by provider. I have put an initial config on the e1 controller card and once i got the Channel group configured I put a config on the serial interface. i am a little unsure of how to progress the config a...
Hi, how can i check whats the port speed negotiation by default on a CM 4.2?can i change this, by default?Thanks in advanceCesar
Hi guys,Has anyone seen this error in RTMT (Alert Central):SyslogSeverityMatchFound events generated: SeverityMatch - Alert mgetty[32057]: clean_line: got too much junk (dev=ttyS0).: SuccessThis Alert is appearing in syslog/RTMT every few minutes. It...
I have the following deployment:CUCMBE 8.5, CCM-Manager 7.1, 2921 voice gateway (IOS c2900-universalk9-mz.SPA.150-1.M4.bin), Phone load SCCP45.8-5-4SAll phones register to CUCMBE just fine but when I test my SRST gateway, the phones do register but t...
So we upgraded our desktops to Windows 7 and I've got Attendant Console (I believe it's version 6.x) running in an XP VM on a new Win7 pc. It installed fine and connects to CUCM. Inbound calls are shown on the screen.But, no free/busy data is being...
I am attempting to calculate the WAN bandwidth requirements for a CUCM and CUCCX cluster over the WAN. The scenario is a CUCM and CUCCX first node in location A and a CUCM and CUCCX secondary nodes at location B. BHCA is not known however there are...
Hi,To use ip phones 7900 series with UC business edition 8.X, we must upgrade basic license to enhanced or not?Thanks in advance ProductDescriptionUNIFIED-CMBE5KUnified Communication Manager Biz Edition 5000 - Top LevelMCS7828I5-K9-BE8BCMBE5K 8.X, 7...
Is there some documentation on the maximum calls on the IAD2431-1T1E1 in a sip to sip gateway scenario?
Symptom:When calling from CUCM 7.1(3) IP phone to CCM 4.3(2) IP phone across the ICT trunk, the 1st call attempt is always a fast busy, but the 2nd call attempt completes sucessfully.When I change the Device Pool and Callmanager Groups for the CUCM 7...
Guys I just upgrade a Cisco 2851 router with ccme 4.2 (c2800nm-advipservicesk9-mz.124-11.XW10.bin) (cme-124-11XW2) and now I can't establish calls from ATA 188(h323) nodes to the Main Site(2851). When I try to call from an ATA of a remote site to the...
Hi all,It seems that 8900 series does not support IPMA, is it true ? (CCM 8.5.1)Is it written anywhere, I can't find it. Is there any roadmap about adding such feature to 8900 series.Regards,François tetard
Hello,I'm getting a SIP message "SIP/2.0 486 Busy here" on certain calls to the PSTN. My setup is:CUCM-----SIP---->CUBE----SIP---->PSTNOn the SIP debugs, I see the call being setup:Received: INVITE sip:<<called #>>@<<CUBE IP>>:5060 SIP/2.0Via: SIP/...
I have some Polycom 335 sip phones that do not seem to pass their dtmf tones correctly when the digits are press for an AA. All of my other devices including a sip ata that is trunked to CM are able to talk with the AA just fine. I can't seem to loca...
| User | Count |
|---|---|
| 8 | |
| 4 | |
| 3 | |
| 1 | |
| 1 |
