Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hello Everyone, We have Cisco Unified CM 10.5 and want to forward call from specific number to another number, but the other calls not forward.Does anyone have an idea how I can do it?
Dear All, I hope all of you are doing well.In my organization, we have CUCM version 11.5 installed, along with 250 Cisco 7821 IP Phones that have been configured since 2018. Unfortunately, we are currently facing issues with the IP Phones, and the fo...
hi I have a 2900 router VERSION c2900-universalk9-mz.SPA.157-3.M2.bin CME 12.0 I have a problem with 7942 IP phones that are unable to download the filmware after I have done the reset procedure, instead the 7975 ip phones even after i reset them the...
We are using Version 15.5 and ip phones of 7975. Recently, I have noticed that some external callers' name appears eventhough they are not in our address books or fast dials. Strange that just weeks ago same callers (i checked the logs) only appea...
Hello,When i navigate to network settings->ip address there's no edit button displayed. When i press " * * # " The "EDIT" button appears, but it's grayed (disabled). How to enable it? Thank you.
Hello!As there are quite a few people out there myself included who have responsibilities that include both a Cisco CUCM v14 in a network along with an Avaya system in this case Avaya CS1000 I was looking for general feedback for what things should ...
Hello, I was wondering if this is possible. This request comes from the contact center that is using cisco CUBE to receive and send calls to the sip provider. This is SIP to SIP They are asking if it is possible to send sip messages on multiple por...
Hello, I would like to Ask a question. I have users in the Call pickup group (visual signaling, timer set to 15 seconds) . If the user A is in Call and another call comes in, the users stated that then immediatelly rings the call on another phone....
I am a bit new to the Cisco phones so please keep that in mind.We are using 6945's and when I go into CUCM->Phones-><my phone> and check the Extension Mobility box to enable it, I apply the config and after the phone applies it, I still don't have th...
This seems like it should be simple, so I'm probably missing something basic.ISR 4351 Router running 17.6 firmware. We're using auto register to connect 8851 phones. Everything is fine except for one little problem. The preferred codec keeps showing ...
Hello,I recently bought some 8821 to install them under asterisk 13. I am using the latest SIP firmware 8821.11-0-6-7 and my phones seems they are working as expected without issues while I install one single SIP account per phone. If you try to add ...
Hi, I have an ATA 191 box, and I'm trying to configure two lines.When I configure the 2nd line, it appears under the "Unassigned Associated Items" section.When I try to reorder the phone button configuration, I get an error: "Fixed feature buttons ca...
Cisco Support Forums, We are switching out a firewall that has SIP ALG to a Meraki firewall that doesn't do SIP ALG. There is a Cisco 4321 that is running as a CUBE, it has a private IP interface that is NAT'd from the outside, so now without SIP...
We have a Cisco Model ISR4451-X/K9 router with Cisco IOS XE Software Version 16.03.05 as H.323 voice Gateway and Cisco Call manager version: 11.5.1.22900-28. Voice gateway connected to PSTN with 4 PRI (E1/T1) ports.I set “Mobile Number A” for Directo...
Hi everyone.I have a cisco 2811 with FXO modules that is connected to an Asterisk IPPBX server. Every thing is working fine. But there is a problem with DID. I'm using connection-plar 2000 for forward incoming calls to asterisk. Therefore I can not f...
