CAE: UCS Quick Start Guide Author: Kristin Duran, kduran@cisco.comTable of Contents Preface. 3Introduction. 3Prerequisites. 3Sample Topology. 4Managing UCS. 4Console Connection. 4UCS Manager GUI 5UCS Ma...
CAE: UCS Quick Start Guide Author: Kristin Duran, kduran@cisco.comTable of Contents Preface. 3Introduction. 3Prerequisites. 3Sample Topology. 4Managing UCS. 4Console Connection. 4UCS Manager GUI 5UCS Ma...
When a new release of UCS code is released you need to do a few things in sequence, and add these all together you get something called "UCS Upgrade Standard Operating Procedure".STP001Notification of ReleaseSTP002Research and Plan the ReleaseUCS...
When a new release of UCS code is released you need to do a few things in sequence, and add these all together you get something called "UCS Upgrade Standard Operating Procedure".STP001Notification of ReleaseSTP002Research and Plan the ReleaseUCS...
Dave Alexander is a UCS expert and trainer at Cisco and runs a brilliant UCS blog at http://www.unifiedcomputingblog.com/ < CHECK IT OUT!He just posted a great tip that I thought needed to be syndicated here for support. Great work, Dave, keep 'em c...
I recorded a sub-3 minute video demo on locating and fixing Faults in UCS Manager.As I can't seem to embed the video, here's the link :-/http://www.screentoaster.com/watch/stU01QRkxIR19aQl1aU1JeUlJWFree online screencasting tool
When a new release of UCS code is released you need to do a few things in sequence, and add these all together you get something called "UCS Upgrade Standard Operating Procedure". Here's what the summary of that SOP looks like:Be notified of the rel...
When a new release of UCS code is released you need to do a few things in sequence, and add these all together you get something called "UCS Upgrade Standard Operating Procedure".STP001Notification of ReleaseSTP002Research and Plan the ReleaseUCS...
Hi,i'm looking for the installation guide for the 6509 switch.please provide me the link for the same.Thanks
IntroductionTerminologiesBMC - Baseboad Management ControllerUsing KVM Connection to Setup the Blade Server IntroductionAlthough not required but readers are highly encouraged to get familar with the concepts discussed in the following document first...
IntroductionThis document describes the procedure and concepts that can be used to configure the UCS for the networking on your LAN network. There could be many different VLAN configured in a LAN environment for different applications and purposes. F...
Dear ALL:My old CSS 11155 Switch has error messg. when boot...from Diag port show that:28 NVRAM Data Bus ------------------------------------- (01)-ERROR>>FAILURESTART ***************************************Fault Environment: ModType:SCFM Devi...
How can I allow the ACE 4710 to route traffic to an IP address on the same subnet on which it was recieved? So the server sends a packet to its default gateway (the load balancer) 1.1.1.1/24 and the load balancer should route back out the same inter...
ScenarioYou have several Service Profiles that are associated to blades and running vSphere's ESX4. You have a new network VLAN to make available to vSphere so you need to do three things - all of which are NON-DISRUPTIVE CHANGES, which means NO REB...
IntroductionUCS B-Series blade servers come in two form factors: full width and half width. Both of these types of blades are based on x86 architecture and come with dual Intel Xeon 5500 series quad-core processors. These blades support DDR3 memory,...
IntroductionFibre-channel SAN is a great design choice for UCS because it enables high-performance, reliable, stateless computing.High-performance because fibre-channel is the best performing block-storage device, and stateless because Boot-from-SAN ...
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: