Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
We have CUPS 8.6.3.10000 and CUCM 8.6 is on production.Configured Cisco Jabber 9.0.1 for windows and able to login to Jabber.Integrated with LDAP, CTI Gw, CCMIP, CFS all are created.Problem I am facing in Jabber is for any user under communication i...
Hi TeamAny suggestions on how to troubleshoot beep tone on some 7942 Phones?The problem is intermittent. We have a UCCE Setup and calls are auto answered. For some incoming calls the 7942 produces a beep before the call is answered. Its something lik...
Hello,I have a strange issue. When pressed Directory list on Cisco 7937 SCCP phone, it shows the directory list for a fraction and shows XML Error 4. CUCM version is 8.5.1. Phone load is apps37sccp.1-4-4-0. Could someone help me.Karthik
Hello all,I am installing a new 2 xUCS-C220 server CISCO BE6K-ST-BDL-K9. When trying to build the Call Manager BE6K side.After deploying the OVA and trying to install the Virtual Machine in ESXi I get the following:Products not supported on this plat...
HiWe have connected CUCM with Avayia via Qsig Call Flow:CUCM--H323 VG-QSIG ---AVAYAEverything working ok but i am wondering if we can do the below scenarioWe move some extensions from Avayia to CUCM and we need these extensions for outgoing calls ...
Hello,Do we have a procedure document for replacing MCS7945 I3 server from the existinf CUCM cluster with a new server and adding it back to the cluster.Please share any doc if you have one.Thanks in advance..Regards,Sargam Patne
Hi guys,I have a problem with the Busy Trigger option on the CM (8.6.2).The phones have 2 Lines. on the first line there's:Maximum Number of Calls: 2Busy Trigger: 1ont he second line which is a shared line:Maximum Number of Calls: 5Busy Trigger: 2If ...
Hi all,I'm trying to install a SIP firmware (SIP894x.9-2-2-0) on a Cisco 8945 Phone.The is connected on a CME 9.1 and SCCP is working fine.THe "debug tftp events" show no error, but the phones still keeps the SCCP image.Here the config:voice register...
Hi again cisco techs.Have been scouring google re the above and getting mixed answers dependant on the search criteria used each timeEach 79xx phone will use SCCP firmware via I suspect cme 4.1 (unless told otherwise) to connect upWhat is the softwar...
hello,i did a reset factory to the cisco ip phone 7911 but it can't load the default firmware it shows only cisco. how can i resolve this problem?
Can any one say to me which certificate of CUCM to add to my pc in order to not be prompted every time when i use click to call?I mean what is the extension (.what?)Thanks.
Hello.I’m installing a BE6000 8.6.2, and the Install disk of the Cisco Unified Comunication Mgr Unity Connection/BE/SME is damage can’t be read.Try to download it from Cisco Support but couldn´t find the file, only found Service Update, Recovery Disk...
CCM5.1.3--CUBE--ASA(NAT)--CarrierFollows ASA configuraiton and debugging which get fast busy when dial out to Carrier. Please guide me what's wrong in the ASA configuration.Thanks in advance,10.0.12.10=CUBE IP@x.x.x.1=public@ mapped to CUBEy.y.y.1=Ca...
I currently have 12 remote offices, which all have a Cisco 2921 H.323 gateway. All offices use the centralized CUCM 8.5.1 cluster that is in Chicago.All offices have a 20Mb SIP Ethernet loop to the MPLS network. We are not using PRI's or T1s. On o...
Hi there,We have a CME (Version 7.1) and I would like to change the "call-forward noan" number through the phone...so that the user can decide,to with number the call should be forwarded. Only 2 numbers are used. Has someone a clue, or do I need to d...
